POLY Treatment Protocols

On this page you will find our recommendations for treating clients with POLY. The protocols listed below are for a variety of treatment types using different LED wavelengths to manage different indications.

Please Note: The following protocols are merely a recommendation based off of client response from usability studies and clinical feedback. All LED treatment regimens should be discussed between the client and POLY user.

Please Note: If the treatment process is combined with drug use, then it should be noted that the drugs are not part of POLY’s therapy. The judgement on how to use drugs should be made by a qualifying physician.

Please Note: If symptoms such as local, mild prickliness and discomfort, skin dryness, erythema, or itchiness occur, they can be treated with a cold compress. These side effects may also be mitigated by reducing treatment time.

Scroll down to see our full list of treamtent protocols for our entire POLY line. We have protocols for:

  • POLY Rejuv
    • Red light treatments for skin rejuvenation
  • POLY Clear
    • Blue light for acne treatment
    • Blue/red light combination for acne treatment
  • POLY Regen
    • Red/infrared combination light for pain management
  • POLY With Adjunctive Treatments

 

 

POLY Rejuv Protocols

Using POLY Rejuv for Skin Rejuvenation:

  1. Wash and cleanse the face
  2. Exfoliate the skin (optional)
  3. Apply pre-treatment serums/peptides (optional)
  4. Position client under POLY, provide optional goggles. Be sure to position the panels at least one inch from the nose to maximize the curve around the face. If treating the body, place panels 1-2 inches from skin.
  5. Following the manual instructions, activate POLY, select wavelength, set the treatment timer, and begin treatment.
  6. Give POLY Rejuv treatment for 15 minutes.
  7. Wait at least 24 hours between sessions.
  8. Continue POLY Rejuv treatments 2-3 times per week for a total of 8 weeks.
  9. Once the initial round of treatments has been completed, speak with your provider about recommended maintentance sessions.

 

POLY Clear Protocols

Using POLY Clear for Acne:

  1. Wash and cleanse the face
  2. Exfoliate the skin (optional)
  3. Apply pre-treatment serums/peptides (optional)
  4. Position client under POLY, provide goggles (mandatory)
  5. Give POLY Clear Blue Light treatment for 13 minutes.
  6. Wait at least 24 hours in between sessions.
  7. Continue POLY Clear treatments 2-3 times per week for a full 8 week course of treatments.                                                                                                                                               If giving POLY Clear treatments with Red and Blue light:
    1. Alternating: Give blue light therapy first, then give 15 minutes of red light therapy 24 – 48 hours later.
    2. Combination: Give both blue and red combination therapy at the same time for 22 minutes per session, ensuring 72 hours between sessions.

POLY Regen Protocols

Using POLY Regen for Pain Management:

  1. Position client under POLY and provide optional goggles.
  2. Give POLY Regen treatment for 20 minutes.
  3. Wait at least 48 hours in between sessions.
  4. Continue POLY Regen treatments 2-3 times per week.

POLY With Adjunctive Treatments

Microneedling – Wait until bleeding and swelling to subside after a microneedling session and after wiping the treatment area clean, begin LED treatment.

Microdermabrasion – Administer LED treatment after microdermabrasion session to ensure safe administration.

Peels – Since peels can cause warmth on the skin, either adminsiter LED therapy before the peel or after the peel is no longer active. This time may vary depending on the peel used.

Waxing – It is recommended to administer LED therapy after a waxing session is completed.

Want To Learn More About Using POLY? Contact Us Today.

10 + 11 =